Points for attention in the use of microbial pesticides

1. Grasp the temperature.

When spraying bio-pesticide , it must be controlled at an ideal temperature above 20 °C. The secret is that the active ingredient of this kind of pesticide is composed of protein crystals and living spores. Once sprayed below the above temperature, then The rate of propagation of spores in the body of the pest is very slow and the protein crystals are difficult to exert their effects, often showing no control effect after application. According to the experimental data, the bio-pesticides after spraying are 1-2 times higher than the insecticidal efficiency between 10 and 15 °C between the conditions of 25-30 °C.

2. Do not use in dry weather.

Biological pesticides are also extremely sensitive to humidity requirements. The greater the environmental humidity, the more significant the efficacy of spraying biological pesticides, especially for powdered biological pesticides.

3. Avoid the sun.

Ultraviolet light in the sun has a lethal killing effect on spores. Scientific experiments have shown that direct sunlight for 30 minutes will kill spores by 50% in one fell swoop. After one hour of irradiation, the spore mortality rate is as high as 80%. Therefore, the application time is on a cloudy day or after four in the afternoon.

4, after use, afraid of heavy rain wash.

Spores are most afraid of heavy rain, so it should be carried out according to the weather forecast, because the rain will wash away the sprayed bacteria and lose the lethality.

5, avoid mixing with fungicides .

High Speed Door Accessories

About high speed Door Accessories:

1.Driving system: High Speed Door Servo System motor and control, motor SNMA / SEJ +reducer+flang+encoder+control box

2.Other accessories: Middle aluminium bar, bottom aluminium bar, aluminium vertical track, stainless steel vertical track, brushes,round nylon strip, PVC roll, rolling steel tube complete, drum be;;s for rolling tube, side end covers, stainless steel cover, steel tubes, air bag sensor system, safety light beam, Microwave sensor 24 Gigahertz,PVC welding machine, smoke and fire sensors, PVC transparent window, magnetic loop, photocell, remote control, manual push button, sound warning alarm Led lamp traffic light

For some main accessories, here is detain introduction:

1).24G radar sensor:

Brand: Hofic

Technology: Microwave processor

Maintain time: 0.5s

Protection: IP54

Transmitting frequency: 24.125GHz

Maximum installation height: <5meter

Transmitting power density: <5mw/cm2

Power consumption: <1W(VA)

Installation angle: 0-90°(lengthways) -30-30°(crosswise)

Supply voltage: AC&DC 12V-30V

2).Photocell:

Approval CE & ISO9001

Power supply AC/DC 12-30V

Static current 25A

Action current 40mA

Mounting distance Max 10m

NO or NC contact Done by NO./NC. contact selection

Working environment temperature -42℃ to +45℃

Working environment humidity 10 to 90%RH

Appearance dimensions( controller) 123*50*32mm(L*W*H)

Appearance dimensions(Magic eye head) 19*13mm(L*D)

3). Remote control

Operating Voltage: AC220V/50HZ+-20%

Transmit power:≤100mW;Super regenerative module, strong anti-interference

Operating temperature:-30℃-+70℃

Working frequency: 433MHZ;transmitter 1527, millions of encoding chip

Accept sensitivity:≤110dB

Manipulation method: electric remote control

Configure the quantity: Wireless number; factory configuration transmitter two. Can be equipped with PT2272 digital decoder chip

Configure the function: Up, down, stop, anti-lock full-featured reproduction

4). Magnetic loop

Voltage: 12V AC/DC +-10% 24V 115V AC+-10% 230V

Power: <2VA

Continued electrical output: 7A / 250V AC

Frequency range: 20 to 200K Hz

Response time: infinity (factory setting) or adjust maintain time

Sensitivity: 0.01% to 0.1% divided into 3 levels

Protection level: IP30

Electromagnetic compatibility (EMC) Complies with EM50081-1 and EN50082-2

Detection loop inductance: the limit of 40uH to 100uH ideal value 80uH to 300uH

Operating temperature: -25 ℃ to 70 ℃

Storage temperature: -40 ℃ to 85 ℃

Relative humidity: <90% non-condensing

Temperature compensation: automatic compensation up to 50 ℃ / h

Connection type: 11 pin DIN rail socket

Dimensions: 41 * 78 * 85 mm (width * height * length)

Weight: 250 grams

5). manual push button

This exit switch button is made of ABS and has built-in indicator light make it looks more elegant and fashionbale. It can be widely used in public entrance gates, public door, home, office, hotel, etc.

Door Exit Button Push To Exit Switch Door Opener For Access Control Security

Main Feature

Fashionable appearance

Made of ABS Plastic

Easy to install and operate

Used for access control

Specification

Mechanical Life: 500,000 test

Material: Plastic

6). Limit switch encoder

Voltage: DC5V-24V

Output voltage: high voltage≥85%Vcc, low voltage≤0.5V

Maximum mechanical speed:6000rpm

Anti-vibration: 50m/s,10-200HZ,XYZeach way 2 times.

Current consumption:≤30mA

Response frequency: 0-100KHZ

Protection: waterproof,oil proof,dust prevention, IP54

The output code system: binary code

Operating life: MTBF≥30000(+25℃,2000rpm)

Rotational inertia:4.0x10-8kgm²

Maximum load:radial direction20N

Axial direction:10N

Weight: about 0.4kg

High Speed Door Accessories,High Speed Door,Electronic High Speed Door Accessories

Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hffastdoor.com