First, engineering design

1. The engineering design must be calculated and tested for strength design. The production, installation, and acceptance are only based on the standard atlas and the type inspection report provided by the profile manufacturer. This is an erroneous and even dangerous behavior. Because the standard atlas is only a partial diagram of a certain series of windows, it does not indicate the load that the construction can bear according to the diagram, so it cannot be used as a basis for production, installation, and acceptance. For different series of doors and windows (fitting effect drawing), the strength or deflection check or test must be carried out according to the most unfavorable principle of the stress state.

2. The strength and stiffness of landing doors and windows are generally insufficient, and the main force columns (beams) in them must be strengthened.

3. When the height of doors and windows of high-rise buildings exceeds 30M, it shall be carried out according to GB50057 "Code for the design of lightning protection of buildings".

Dikai Windows and Sun Rooms

Second, the choice of materials 1, aluminum alloy profiles must meet GB/T5237-2000 "aluminum alloy building profiles" requirements.

2. The selection and configuration of hardware accessories is one of the important factors for ensuring the quality of doors and windows. Even a window with excellent performance must be guaranteed by the selection and configuration of high-quality accessories.

3. The pulleys, tops, anti-shedding sealers, and lower seal blocks for sliding doors and windows are accessories that ensure the quality of sliding doors and windows. Pulleys are the key to the smooth opening and closing of doors and windows. Roller-bearing nylon wheels should be used. The anti-shedding sealer is a safety measure to prevent the window sash from falling off, and at the same time, it has the sealing function between the hook and the upper slide, and the durable ABS plastic and the EPDM rubber should be used. The lower sealing block plays a sealing role between the hooking rate and the glide path, and can effectively prevent the splashing phenomenon under the effect of the fluctuating load. The EPDM rubber should be used. Tops are the seals of window sashes and window frames, which determine the airtightness of doors and windows. Common chemical fiber slivers will curl and lose their sealing effect. Silicone tops must be used.

4, hinged doors and windows hinges (or sliding window friction hinges), handles, box seals between the sealant is to ensure that the quality of flat doors and windows the most important accessories. The bearing capacity of the hinge (or friction hinge of the sliding window) is the key to the safety of the doors and windows and the smoothness of the opening and closing. The bearing capacity of the hinge is stronger than that of the friction hinge, so the hinge can make a larger window sash For use, friction hinges are only suitable for smaller windows or top-hung windows. Handle the important accessories related to the security of doors and windows and sealing performance. The ordinary handle is only suitable for use on sashes with smaller grids and loads. The multi-point handles for European style (furnishing effect drawings) are applicable to both grids and loads. The larger window sashes are used; the sealing strips between the framed sashes guarantee the airtightness and watertightness of the flat doors and windows, the sealing effectiveness of the native PVC strips is about 5 years, and the recycled PVC strips do not have For sealing effectiveness, it is desirable to use a weather resistant rubber such as EPDM.

5. The model, specification and performance of hardware accessories shall comply with the relevant provisions of the current national standards.

6. Structural adhesives and weather-resistant adhesives used for concealed frame windows should be tested for compatibility with profiles and glass prior to use.

Third, processing

1. The processing of aluminum doors and windows should be carried out in the factory and must not be made on the construction site.

2. The drainage hole on the sliding window chute should be processed according to the principles of the inner and outer fan inner holes to ensure the sealing performance of the doors and windows, especially the horizontal sliding door of the horizontal top bar.

3, before the assembly of aluminum doors and windows, should remove the end processing burrs, end nodes and profile joints must adopt waterproof sealant and other sealing measures to prevent structural water seepage.

4. Hidden frame window structure assembly assemblies must be made and maintained in a clean room.

It is necessary to remove dust, oil stains, and other contaminants from the surfaces of the glass and aluminum frame with a solvent; every clean of one component or glass should be replaced by a clean dry cloth; the solvent should be poured on the cloth, and the cloth must not come in contact with the solvent bottle mouth. The glue must be full and no bubbles or leakages should occur. The surface of the glue joint should be smooth and smooth; the remaining glue that receives the glue joint must not be reused.

Fourth, installation, product protection

1. Check the shape and position accuracy of the door and window (fitting renderings) before installation. Check and check the number and position of the embedded rakes. Check if the high-rise windows are connected to the lightning protection belt according to regulations. For unqualified Some should urge the construction unit to reform.

2. The doors and windows of the oxide material caulked with cement mortar should be preserved before the wall. Except for the outer wall, the other surfaces of the window frame are protected with adhesive tape or plastic tape. There must be no adhesive tape or plastic tape on the wall surface to avoid water seepage in the joint.

3, doors and windows on the wall after the use of wooden wedges to adjust the positioning, and then fixed with a nail, can not be fixed with iron nails, wooden wedges. Before the caulking, the supervising unit (or construction unit) shall be required to make a concealed project acceptance record, and check the vertical, horizontal and diagonal lines of the doors and windows, and the wooden wedge shall not remain in the seam after caulking.

4. Waterproof glue between window frame and wall must be done after the wall is dry. If the wall is not dry and the dust is not removed, the water vapor released from the wall will invalidate the seal.

5. After the wet operation is completed, remove the protective tape or plastic tape and the dirt from the window frame before installing the glass and sash.

6. After installation of glass and sashes, check whether the fittings are leak-proof, the installation is firm, and the window sashes are open and closed flexibly. Before the acceptance, open the fenestration windows should be closed to prevent the window sash from being damaged due to the storm.

7. Before the acceptance, the aluminum doors and windows shall be cleaned and self-inspected, and the corrosive cleaning agents for aluminum profiles, glass and hardware accessories shall not be used; problems arising from self-test shall be promptly rectified.

V. Project acceptance

1. Acceptance of aluminum doors and windows project shall be carried out in accordance with GB50300 "Unified Standard for Acceptance of Construction Quality of Building Engineering" and GB50210 "Quality Acceptance Criteria for Building Decoration Engineering".

2. The acceptance of the aluminum doors and windows project shall be based on the acceptance of the concealed project and the self-check of the construction unit.

3, the project inspection should check the following documents and records:

3.1 Door and Window Production Licenses and Installation Qualification Certificates.

3.2 Engineering design calculation book, design specification, construction drawing, door and window three-quality inspection report, aluminum door and window product quality certificate, concealed project acceptance record, installation and construction self-inspection record and aluminum profile, glass, sealing material, hardware accessories product certification , Quality Assurance Documents and Acceptance Records, in which aluminum profiles, safety glass and structural adhesives should also provide reinspection reports.

3.3 Hidden frame windows shall also provide the compatibility test report of structural adhesives and weatherproof adhesives, and the temperature and humidity records of the glue and maintenance environment. Domestic rubber should provide product production certification, imported rubber should be supplier inspection certificate.

Sixth, special attention should be paid to the installation and construction of coastal areas

Due to the large amount of saline and alkaline contained in the coastal areas, there are some areas that have not been treated with desalinated sea sand in accordance with the national standards. Corrosion problems of aluminum alloy doors and windows (fitting renderings) are serious and should be given special attention. The importance attached. In addition to the above procedures, the following procedures should also be strictly followed:

1. The aluminum doors and windows brought into the construction site should be placed in a well-ventilated, dry and clean warehouse.

2. The height of the sleeper surface of the place to be placed above the ground should be ≥100mm, each pile should not exceed 15 樘 (fan), and a soft material levelling should be applied between each 樘 (fan) to prevent the pressure between the aluminum alloy and the hardware. Frictional damage to the protective film on the surface of the profile.

3, door and window openings must have a drip line, should be tested before installation. Because the rainwater flowing through the wall made of sea sand is highly corrosive, it must be guarded against.

4, the installation of iron sheet should adopt the card type, to minimize the destruction of the protective layer of aluminum alloy processing.

5. The aluminum alloy section joint is sealed with a neutral gel to prevent rainwater from entering the inner cavity without a protective layer. As a rule of thumb, corrosion usually begins in the interior without a protective layer.

6. After the interior and exterior decoration is completed, tear off the protective tape and clean the doors and windows. Do not use corrosive liquids and hard objects to clean the doors and windows so as not to damage the surface paint film.

7, important tips:

1) Aluminum is an active metal. The damage of the protective layer is not anticorrosive, and it is prone to corrosion. The necessary measures should be taken to strengthen the protection of the paint film on the surface of the profile.

2) Water is the source of corrosion, and rainwater should be prevented from entering the interior of aluminum alloy profiles without corrosion protection.

Precautions Door & Window Villa Design Window Glass Aluminum Alloy Decoration Design Window Effect Picture Interior Decoration Effect Picture Exterior Decoration Effect Picture Sun Room Decoration Effect Picture European Decoration Effect Picture Glass Sliding Door Glass Door

Elevator Safety Components

The safety protection system includes various mechanical and electrical protections. The five major components include: safety gear, speed limiter, door lock, buffer, rope gripper and uplink overspeed protection. In order to effectively avoid frequent elevator accidents, we should do a good job in elevator safety devices and inspection, eliminate hidden dangers and ensure elevator safety. We are manufacturer of Elevator Safety Components in China, if you want to buy Elevator Safety Devices, Elevator Safety Components And Systems, Industrial Elevator Safety Parts, please contact us.

Elevator Safety Components,Elevator Safety Devices,Elevator Safety Components And Systems,Industrial Elevator Safety

Suzhou Stable Trade Co., Ltd , https://www.stable-elevator.com