Saving is a kind of virtue, this applies to the whole world, so now many bathroom products have the design of saving water, especially toilets, which use more water, more water-saving design is needed. What is the water-saving toilet ? The design here? Xiaobian to recommend five common water-saving toilet design.

1. What is the water-saving toilet?

Water-saving toilets should be under the premise of ordinary toilets, and they can also save water in a limited way. It must ensure that the basic requirements for toilets are clean, non-returned and not blocked.

The toilet uses a water-saving design that not only saves the Earth’s water resources, but also reduces problems such as sewage treatment, saves water and reduces pollution, and also reduces the user’s various cost issues. It is a very promising and resource-efficient design. Therefore, it is very necessary for households to configure water-saving toilets.

The design of the water-saving toilet is mainly based on the water tank and accessories, control method and installation. The sewage outlet at the bottom of the toilet is connected with the sewage drainage pipe. Here, a sealed movable baffle connecting the upper cover is installed, and a piston pressure device is arranged in front of the toilet. The built-in water stop valve has high water-saving efficiency and reduces the amount of sewage discharged.

2. Introduction of five common water-saving toilets

a, pressure flow deodorant water-saving toilet

The design of this product is a combination of ceramic sealed interlocking influent irrigation device, magnetic separation sewage seal device, toilet seat body and other accessories, which eliminates S bends, effectively prevents the backflow of various gases and liquids, single valve linkage The water type is accurate and easy to use. There are large and small urine water for automatic binning and water tanks. It is easy to install and saves space.

b, pressure flow impact water - saving toilet

Mainly by the combination of water-saving water tank, breathing valve, inlet valve, over pressure valve, ceramic water tank, water inlet pipe, water pipe connector, water-saving toilet, etc., in which the breathing valve can ensure the pressure of the closed water tank, and the control valve makes the gas in the upper part of the drainage valve pass through. The pressure relief tube is connected to the outside and can be flushed without the need for 4L of water. It is suitable for both drainage and siphon drainage.

c. Two-button water saving toilet

This design is similar to an ordinary toilet. There are two buttons to control the flow of water. You can also see the flushing situation to reset and reduce water consumption.

d, pedal type high efficiency water-saving toilet

This kind of design uses the foot movement method to control the water flow, has the characteristic of preventing the virus from infecting, is suitable for the direct-discharge drainage method, and has 3 deodorant measures, and the effect is particularly good.

e, induction water - saving toilet

Displacement is controlled according to the length of time, and its water level can be adjusted.

Editor's Sum: The above is about the water-saving toilet is what and five kinds of common water-saving toilets introduced, water-saving toilets are very popular with consumers now, but many of the water-saving products on the market are fake imitation , so the best choice is to judge, you can choose some big brands more at ease.

PEI plastics (polyetherimide plastics) is an amber transparent solid. It has an inherent flame retardancy and low smoke concentration without adding any additives. The oxygen index is 47%, and the combustion level is ul94-v-0, and the density is 1.28~1.42 g/cm3.

PEI plastics has a strong thermal stability, and even the non-enhanced PEI plastics still has good toughness and strength.Therefore, the high thermal stability of PEI plasticsis used to make high temperature heat-resistant devices.

PEI plastics has excellent mechanical properties, electrical insulation performance, radiation resistance, high temperature resistance and abrasion resistance, and can be used by microwave.The PEI plastics also has good flame retardancy, chemical resistance and electrical insulation.Vitrification transformation temperature is very high, up to 215 ℃.PEI plastics also has a very low shrinkage rate and good mechanical properties.Adding fiberglass, carbon fiber or other fillings to enhance the purpose of modification;And other engineering plastics of heat-resistant polymer alloys, can be in 160 ~ 180 ℃ under the working temperature of use for a long time.

The long-term use of polyether amines in the us underwriters laboratory is 338T and 356T (according to the grade), and the combustion rating reaches UL94V - 0 (10 mille thickness).The oxygen index is 47, and the polyetherimide is in line with the requirements of the aircraft for the requirements of the FAA's flame retardant and thermal release material standards.It has a glass transition temperature of 419F and is allowed to be used intermittently under 392F, at higher temperatures, resulting in a short-term shift.Under 356T, the tensile temperature and flexural modulus were above 41 and 2068MPa respectively.The material reinforced with Glass Fiber and carbon fiber has higher strength and rigidity under the transition temperature of glass.

PEI plastics long-term resistance to creep under high temperature and stress allows it to replace metals and other materials in many structural devices.PEI plastics shows good performance in variable temperature, humidity and frequency.The low dissipation factor at GHz frequency makes the polyetherimide have high microwave wearability.Its ionic pollutant is low, at 250F100 % R.H.And 207kPa after 120 hours of water extraction with the conductivity, at 20 megaohm, it can be used as an electronic sensor element insulation.

PEI plastics is a fine coating and film forming material which can be used for the coating and film of electronic industry, and can be used in manufacturing aperture < 0.1 mu m, with high permeability microporous diaphragm.It can also be used as high temperature adhesive and high strength fiber. 

Application field

Since PEI plastics has excellent comprehensive and balanced performance, PEI plastics has been applied to the departments of electronics, motor and aviation, and used as metal substitute materials for traditional products and cultural life supplies.Using PEI plastics instead of metal to make optical fiber connector, PEI plastics can optimize the structure of the component, simplify its manufacturing and assembly steps, and maintain a more precise size.Used in automobile industry, such as high temperature fittings for manufacturing, the high power lamp and light, control the car cabin outside temperature sensor (air conditioning temperature sensor) and the control of air and fuel mixture temperature sensor (effective combustion temperature sensor).Also can be used for high temperature erosion of lubricating oil vacuum pump impeller, distilling apparatus that operate at 180 ℃ of ground glass joints (following), the lighting of anti fog light reflector.

PEI Plastic Sheet

PEI Plastic Sheet,Polyetherimide PEI Sheet,Esd PEI Plastic Sheet,Extruded Plastic PEI Sheet

Dongguan Noegem Plastic Products Co.,Ltd , http://www.noegempLastic.com